The Rockler Cross Cut Sled (table Saw Sled)




People Who Liked This Video Also Liked

the Rockler cross cut sled   (table saw sled)
the Rockler cross cut sled (table saw sled)
crosscut sled | 5 cut | how to | dave stanton | rockler ideas
crosscut sled | 5 cut | how to | dave stanton | rockler ideas
In the Shop tests the Rockler crosscut sled
In the Shop tests the Rockler crosscut sled
Four Reasons to Use a Table Saw Crosscut Sled | Rockler Skill Builders
Four Reasons to Use a Table Saw Crosscut Sled | Rockler Skill Builders
How to Use a Table Saw Cross Cut Sled
How to Use a Table Saw Cross Cut Sled

Did this video help you?

Moon Pie: Made my own - this stuff is way over priced.

Fochopz: Did you use the 5 cut method to check for square of the sled fence? Just curious how true to 90 it is.

Mark Miller: Nice bit of kit

Richard Roby: Nice truck. I have a 02.

Robert Vander Voort: I'm not sure what all the hemming and hawing is over the cost of this sled. It's completely versatile.

There are all sorts of miter fences from Incra, Osborne and the like, a good one new starts about 70 bucks.... I use one with a dado blade to make half lap and box joints.

This tool is a pretty clever design. The method of setting miter angle looks pretty good to me. To make the equivalent to purchase the hardware and wood, you're going to spend some money and time.... it's just a matter of how a person wants to direct those two resources.

Does the sled work as advertised? How much utility and accuracy, ease of setup?

The need for the peanut gallery to point out that $140 is a lot of money- I can do without. Damn near everyone throws their money around it's just a matter of where.

your face: Just make one

barbara kvistad: Have you made any jigs for this sled, such as spline, tenon,?

Noble Roofing & General Contracting: Thank you for speeding it up!

ri mar: eh. falling off cuts next to the blade, because of the design nature is goofy. sure the danger is small if the pieces are thin/short. once you move into longer/thicker lengths you'll probably need the more traditional sled design. so unless you want multiple sleds by all means. it at least looks pretty!

Neil Brown: I took the slot bar off to adjust the fit in the slot,I was then able to set each tension ball one at a time,far easier than with it attached

nick danger: you made some sleds and they sucked? I made 4 different ones for my $100 aluminum Ryobi in a week and none of them suck. A big one, a small one, a 45 degree jig and a jig for notching picture frame corners for a strengthening piece. Protractor sled is next on my list. At least I got some ideas from your video.

artincorona: When you square it up with the blade does it allow you to reset the fence to 0 degrees? Or how does that work when squaring up?

robslifting4life: 140$ haahahah of course... freaking rocklers

Jim Ryan: Thank you for posting. Thank you more for NO music. But I have grown to really not like the sped up videos, they give me a headache.

Colins DIY & MTB Barling: Why would you go and buy one when they are so so so so easy to make waste of money
Thought i might subscribe see what else you waste money on lol.

HCAC BUILD: Lol, MDF. That really is a good deal. Can you use it around water?

Gene Schmid: .

HCAC BUILD: $ 140 and they shipped it to you all the way from China. Man, that's a good deal.

Bravo 1969: $140 !!!, I'd rather buy a math book and build one for $0. I can give the math book to my kids that don't do wood working.

Graph Guy: so 9 months later? your thoughts?
Rating:
the Rockler cross cut sled (table saw sled) 5 out of 5

Featured Video

Video How to Guide

Latest Comments

Moon Pie: Made my own - this stuff is way over priced.
Neo Källberg: ITS AA SEMI-AUTOMATIC SNIPER RIFLE!
WildGamerSK: 7.2.5 LATEST update: https://youtu.be/zp2StZSWRls
Andree CB: Son primos
KHOD MUA: https://youtu.be/LsTzzRaGdv0
Trung Tre: Săn cái kiểu này thì hay ho gì. Thú đầy đồng, nhiều như trong chuồng mà săn bắn cái gì
Kiss x Kiss: Like número 800.

the Rockler cross cut sled   (table saw sled)